Conectores de Impresora Paralelo

Nota: la dirección es en el sentido Ordenador -> periférico.

[PC] [Atari ST] [Amiga] [Amiga 1000] [Dragon] [ORIC] [MSX] [Amstrad CPC+] [Amstrad CPC] [Spectrum +3] [Olivetti M 10]

La gran mayoría de ordenadores utilizan el conector SUB-DB-25 hembra, presente en :
  • IBM PC, XT, AT y compatibles
  • Atari ST / STE / Mega / Mega STE / TT / Stacy / Falcon,
  • Apple //con tarjeta de puerto paralelo,
  • algunos clónicos Mac,
  • SVI 318/328 con tarjeta puerto paralelo,
  • Amstrad CPC+,
  • Amstrad PCW con interfaz Serie/centronics 
    		•
    25 PIN D-SUB FEMALE

    PC Estandar

    Pin Nombre Dir Descripción Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 10 /ACK <-- Acknowledge 18 GND --- Signal Ground
    2 D0 --> Data Bit 0 11 BUSY <-- Busy 19 GND --- Signal Ground
    3 D1 --> Data Bit 1 12 PE <-- Paper End 20 GND --- Signal Ground
    4 D2 --> Data Bit 2 13 SELIN <-- Select In 21 GND --- Signal Ground
    5 D3 --> Data Bit 3 14 /AUTOFD --> Autofeed 22 GND --- Signal Ground
    6 D4 --> Data Bit 4 15 /ERROR <-- Error 23 GND --- Signal Ground
    7 D5 --> Data Bit 5 16 /INIT --> Initialize 24 GND --- Signal Ground
    8 D6 --> Data Bit 6 17 /SEL --> Select 25 GND --- Signal Ground
    9 D7 --> Data Bit 7
    Fuente : Manuales del Amstrad PPC 640, Commodore PC 10/20 III, varios clonicos
    25 PIN D-SUB FEMALE

    PC ECP

    El puerto Extended Capabilities Port (bidireccional) se implementa en los PC's mayoritariamente con el bus PCI (placas 486 PCI), al integrar las funciones realizadas antes por una tarjeta Multi I/O (puertos Serie y Paralelo, controladoras IDE y floppy) en la propia placa base. No obstante, puede encontrarse en PC's más viejos equipados con una multi I/O moderna.
    Pin Nombre Dir Descripción Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 nStrobe --> Strobe 10 /nAck <-- Acknowledge 18 GND --- Signal Ground
    2 data0 <-> Address, Data or RLE Data Bit 0 11 Busy <-- Busy 19 GND --- Signal Ground
    3 data1 <-> Address, Data or RLE Data Bit 1 12 PError <-- Paper End 20 GND --- Signal Ground
    4 data2 <-> Address, Data or RLE Data Bit 2 13 Select <-- Select 21 GND --- Signal Ground
    5 data3 <-> Address, Data or RLE Data Bit 3 14 /nAutoFd --> Autofeed 22 GND --- Signal Ground
    6 data4 <-> Address, Data or RLE Data Bit 4 15 /nFault <-- Error 23 GND --- Signal Ground
    7 data5 <-> Address, Data or RLE Data Bit 5 16 /nInit --> Initialize 24 GND --- Signal Ground
    8 data6 <-> Address, Data or RLE Data Bit 6 17 /nSelectIn --> Select In 25 GND --- Signal Ground
    9 data7 <-> Address, Data or RLE Data Bit 7
    Fuente : Microsoft MSDN
    25 PIN D-SUB FEMALE

    Atari ST / STE / Mega / Mega STE / TT / Stacy / Falcon

    Pin Nombre Dir Descripción Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 10 n/c   No Conectado 18 GND --- Signal Ground
    2 D0 --> Data Bit 0 11 BUSY <-- Busy 19 GND --- Signal Ground
    3 D1 --> Data Bit 1 12 n/c   No Conectado 20 GND --- Signal Ground
    4 D2 --> Data Bit 2 13 n/c   No Conectado 21 GND --- Signal Ground
    5 D3 --> Data Bit 3 14 n/c   No Conectado 22 GND --- Signal Ground
    6 D4 --> Data Bit 4 15 n/c   No Conectado 23 GND --- Signal Ground
    7 D5 --> Data Bit 5 16 n/c   No Conectado 24 GND --- Signal Ground
    8 D6 --> Data Bit 6 17 n/c   No Conectado 25 GND --- Signal Ground
    9 D7 --> Data Bit 7
    Fuente : Manual del Atari ST
    25 PIN D-SUB FEMALE

    Amiga

    Presente en todos los modelos salvo el Amiga 1000. Bidireccional
    Pin Nombre Dir Descripción Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 10 /ACK <-- Acknowledge 18 GND --- Signal Ground
    2 D0 <-> Data Bit 0 11 BUSY <-> Busy 19 GND --- Signal Ground
    3 D1 <-> Data Bit 1 12 POUT <-> Paper Out 20 GND --- Signal Ground
    4 D2 <-> Data Bit 2 13 SEL <-> Select (Shared with RS232 RING-indicator) 21 GND --- Signal Ground
    5 D3 <-> Data Bit 3 14 +5V PULLUP --> +5 Volts DC
    (10 mA max)    		 22 GND --- Signal Ground
    6 D4 <-> Data Bit 4 15 n.c.   No Conectado 23 GND --- Signal Ground
    7 D5 <-> Data Bit 5 16 /RESET --> Reset 24 GND --- Signal Ground
    8 D6 <-> Data Bit 6 17 GND --- Signal Ground 25 GND --- Signal Ground
    9 D7 <-> Data Bit 7
    Fuente : Manuales del Amiga 500 y Amiga 2000

    25 PIN D-SUB MALE

    Amiga 1000

    El Amiga 1000, en cambio, utiliza el conector SUB-DB-25 macho con los pines 14 (+5V), 15 (n.c.) y 16 (/RESET) cambiados por los 23, 24 y 25 (Ground) del port de Amiga normal, necesitando un cable adaptador para los periféricos
    Pin Nombre Dir Descripción Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 10 /ACK <-- Acknowledge 18 GND --- Signal Ground
    2 D0 <-> Data Bit 0 11 BUSY <-> Busy 19 GND --- Signal Ground
    3 D1 <-> Data Bit 1 12 POUT <-> Paper Out 20 GND --- Signal Ground
    4 D2 <-> Data Bit 2 13 SEL <-> Select (Shared with RS232 RING-indicator) 21 GND --- Signal Ground
    5 D3 <-> Data Bit 3 14 GND --- Signal Ground 22 GND --- Signal Ground
    6 D4 <-> Data Bit 4 15 GND --- Signal Ground 23 +5V PULLUP --> +5 Volts DC
    (10 mA max)
    7 D5 <-> Data Bit 5 16 GND --- Signal Ground 24 n/c   No Conectado
    8 D6 <-> Data Bit 6 17 GND --- Signal Ground 25 /RESET --> Reset
    9 D7 <-> Data Bit 7

    Dragon 32 / 64 / 128 / 200

    Todos los Dragon (salvo el MSX) tienen un conector macho de cinta de 20 pines
    Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 2 +5V --- + 5 V
    3 D0 --> Data Bit 0 4 +5V --- + 5 V
    5 D1 --> Data Bit 1 6 GND --- Signal Ground
    7 D2 --> Data Bit 2 8 GND --- Signal Ground
    9 D3 --> Data Bit 3 10 GND --- Signal Ground
    11 D4 --> Data Bit 4 12 GND --- Signal Ground
    13 D5 --> Data Bit 5 14 GND --- Signal Ground
    15 D6 --> Data Bit 6 16 GND --- Signal Ground
    17 D7 --> Data Bit 7 18 GND --- Signal Ground
    19 /ACK <-- Acknowledge 20 BUSY <-- Busy
    Fuente : Manuales del Dragon 32, 64 y 200

    Oric / Pravetz 8D

    Todos los Oric y su clon el Pravetz 8D tienen un conector macho de cinta de 20 pines
    Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 2 GND --- Signal Ground
    3 D0 --> Data Bit 0 4 GND --- Signal Ground
    5 D1 --> Data Bit 1 6 GND --- Signal Ground
    7 D2 --> Data Bit 2 8 GND --- Signal Ground
    9 D3 --> Data Bit 3 10 GND --- Signal Ground
    11 D4 --> Data Bit 4 12 GND --- Signal Ground
    13 D5 --> Data Bit 5 14 GND --- Signal Ground
    15 D6 --> Data Bit 6 16 GND --- Signal Ground
    17 D7 --> Data Bit 7 18 GND --- Signal Ground
    19 /ACK <-- Acknowledge 20 GND --- Signal Ground
    Fuente : Manual del Oric Atmos

    MSX 1 / MSX 2 / MSX 2+

    Todos los MSX tienen un conector 14 pins Centronics
    Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STB --> Strobe 8 PDB6 --> Data 6
    2 PDB0 --> Data 0 9 PDB7 --> Data 7
    3 PDB1 --> Data 1 10 n/c    
    4 PDB2 --> Data 2 11 BUSY <-- Printer is busy
    5 PDB3 --> Data 3 12 n/c    
    6 PDB4 --> Data 4 13 n/c    
    7 PDB5 --> Data 5 14 GND --- Signal Ground
    Fuente : Manuales del SVI 738 MSX Sony MSX Hit Bit 20, Sony MSX2 F700S
    25 PIN D-SUB FEMALE

    Amstrad CPC + 464 y 6128

    Pin Nombre Dir Descripción Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 10 n/c   No Conectado 18 GND --- Signal Ground
    2 D0 --> Data Bit 0 11 BUSY <-- Busy 19 GND --- Signal Ground
    3 D1 --> Data Bit 1 12 n/c   No Conectado 20 GND --- Signal Ground
    4 D2 --> Data Bit 2 13 n/c   No Conectado 21 GND --- Signal Ground
    5 D3 --> Data Bit 3 14 n/c   No Conectado 22 GND --- Signal Ground
    6 D4 --> Data Bit 4 15 n/c   No Conectado 23 GND --- Signal Ground
    7 D5 --> Data Bit 5 16 +5 V --- + 5 V 24 GND --- Signal Ground
    8 D6 --> Data Bit 6 17 GND --- Signal Ground 25 GND --- Signal Ground
    9 D7 --> Data Bit 7
    Fuente : Manual del Amstrad CPC+ 464/6128

    Borde de tarjeta 36

    Amstrad CPC 464, 472, 664, 6128
    Spectrum +2, +2A y +3

    Los Amstrad CPC tienen interfaz de 7 bits (D7 no conectado) y la 27 a Masa
    El conector es de borde de tarjeta, con divisor entre los pin 4/22 y 5/23, y el 18/36 no existe
    Pin Nombre Dir Descripción Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 13 n/c   No Conectado 25 GND --- Signal Ground
    2 D0 --> Data Bit 0 14 GND --- Signal Ground 26 GND --- Signal Ground
    3 D1 --> Data Bit 1 15 n/c   No Conectado 27 n/c   No Conectado
    4 D2 --> Data Bit 2 16 GND --- Signal Ground 28 GND --- Signal Ground
    5 D3 --> Data Bit 3 17 n/c   No Conectado 29 n/c   No Conectado
    6 D4 --> Data Bit 4 18 n/e   No Existe 30 n/c   No Conectado
    7 D5 --> Data Bit 5 19 GND --- Signal Ground 31 n/c   No Conectado
    8 D6 --> Data Bit 6 20 GND --- Signal Ground 32 n/c   No Conectado
    9 D7 --> Data Bit 7 21 GND --- Signal Ground 33 GND --- Signal Ground
    10 n/c   No Conectado 22 GND --- Signal Ground 34 n/c   No Conectado
    11 BUSY <-- Busy 23 GND --- Signal Ground 35 n/c   No Conectado
    12 n/c   No Conectado 24 GND --- Signal Ground 36 n/e   No Existe
    Fuente : Manual del Amstrad CPC 6128, Spectrum +3

    26 PIN IDC MALE

    Olivetti M 10

    El M 10 tiene un conector de cinta macho de 26 Pines (TSR 100 ???)
    Pin Nombre Dir Descripción Pin Nombre Dir Descripción Pin Nombre Dir Descripción
    1 /STROBE --> Strobe 10 /ACK <-- Acknowledge 19 GND --- Signal Ground
    2 D0 --> Data Bit 0 11 BUSY <-- Busy 20 GND --- Signal Ground
    3 D1 --> Data Bit 1 12 PE <-- Paper End 21 GND --- Signal Ground
    4 D2 --> Data Bit 2 13 SELIN <-- Select In 22 GND --- Signal Ground
    5 D3 --> Data Bit 3 14 GND --- Signal Ground 23 GND --- Signal Ground
    6 D4 --> Data Bit 4 15 GND --- Signal Ground 24 GND --- Signal Ground
    7 D5 --> Data Bit 5 16 GND --- Signal Ground 25 RESETGND --- Reset Ground
    8 D6 --> Data Bit 6 17 GND --- Signal Ground 26 /RESET <-- Reset
    9 D7 --> Data Bit 7 18 GND --- Signal Ground
    Fuente :     Joakim Ögren, Filippo Fiani